《清掃車的關鍵技術研究環保機械課程畢業設計外文文獻翻譯@中英文翻譯@外文翻譯》由會員分享，可在線閱讀，更多相關《清掃車的關鍵技術研究環保機械課程畢業設計外文文獻翻譯@中英文翻譯@外文翻譯（7頁珍藏版）》請在裝配圖網上搜索。
1、 中國地質大學長城學院 本科畢業設計外文資料翻譯 系 別： 工程技術系 專 業： 機械設計制造及其自動化 姓 名： 張增良 學 號： 05211525 清掃車的關鍵技術研究 在我國，由于清 掃 車發展時間較短，使用數量較少，研究開發人員有限，又沒有專門的研究機構 對其進行研究，所以缺少對清車主要部件的關鍵技術研究，為了提高吸掃式和純吸式清 潔 車設計的 能力，必須對 其主要部件 清掃系統、 風機 、風道系統和除塵系統以及零部件的耐磨性等進行試驗 研究，以提高清掃車設計的理論水平。 1 加強對清車專用 風機 的關鍵技術研究 風機 是清車中一個相當重要的部件， 風機 是清 潔 集塵的心臟部分，大的
2、風量和風壓是高效集 塵的可靠保證， 必須選用高效能的離心式 風機 ，由于清 掃 車的作業工況的不穩定性，因此在選用 風機 時必須留有一定的余量這樣才能保證清掃車在各種路況 下達到完美的集塵效果，由于空間布置的限制 風機 的外形應盡可能緊湊，同時降低噪聲是選擇風 機時考慮的重要因素之一。我國清 掃 車的 風機 與發達國家的有較大差距，目前，我國清 掃 車的 風機 大 多數都采用通用 風機 或由通用 風機 改制的 風機 。由于通用 風機 是為一般用途的通風而設計的，其體 積、耐磨性、防塵能力等都不能滿足清掃車惡劣工況的要求。可以說，目前我國清 掃 車使用的 風機 ， 大大影響了清掃車的性能。因此，
3、清掃車生產企業應加強對清掃車專用 風機 的研究，從 風機 葉片形 狀、葉片材料、進出風口的形狀和位置、加工工藝等進行探討，設計出體積小、風量大、噪聲低、耐 磨的 風機 。 2 壓縮空氣系統的關鍵技術研究 壓縮空氣系統也是清掃車作業動力的重要組成部分，壓縮空氣系統是由底盤發動機提供壓縮空氣 驅動氣缸產生預定動作完成以下各項功能 ：調節盤刷接地壓力、對盤刷起緩沖保護作用， 當遇到凸起地面時會順勢上浮，氣壓的調節在駕駛室內完成， 滾刷兩端各有一個提升氣缸，另一端懸掛在車架上，操縱電控系統使氣缸帶動滾刷完成升降動作， 提升氣缸還可以調整接地壓力，使之與地面有 20o 圓 弧接觸。提升氣缸為液壓阻尼氣缸
4、，保證始終與地面接觸且接地壓力相等，還可起阻尼緩沖作用， 保證滾刷不受沖擊。吸口翹角氣缸可抬高吸口前緣將大塊垃圾吸入，在開始或停止時提升氣缸將吸口 提升或降至地面。 3 清潔集塵系統的關鍵技術研究 清掃集塵系統包括盤刷裝置、滾刷裝置、吸口裝置、和集塵箱等部分，這是清掃車的關鍵部件。 盤刷裝置擔負著清掃和收集護欄附近和隔離帶角的垃圾的任務，它由盤刷及支架、油馬達、擺臂機 構、油缸及支架、鋼絲及滾輪機構擋板及傳動機構組成。滾刷裝置主要是對公路中部大面積的路面 清掃和將垃圾收集到吸口 附近，它由滾刷、罩殼、油馬達、擺動油缸、提升油缸及轉動支架等部分組 成。吸口裝置將吸口經過區域的垃圾經吸口管道吸進集
5、塵箱，主要由吸口、軟管、支架、支撐小車、 吸口提升缸、吸口翹角缸等組成。集塵箱：它是清掃車?yán)占两祪Υ孢\輸?shù)娜萜?，集塵箱門的 開啟和垃圾的傾卸是由底盤發動機動力輸出接口驅動液壓油 泵 提供動力的，在集塵箱中有沖 擊板，折流板，尾部還有長方形鐵絲濾網，這些板塊增加 了氣流的碰撞效果，易于垃圾從氣流中分離沉降。另外掃刷接地壓力的大小，不僅影響清掃車的清 掃效果，而且對掃刷的磨損也產生重大影響。我國清掃車的掃刷接地壓力是由清掃車操作人員手動 調整，一般情況下，操作人員最多只是在出車時對掃刷接地壓力進行調整，有的甚至是幾天才對掃 刷接地壓力進行一次調整。這種掃刷接地壓力的調整方式，使清掃車作業時的
6、掃刷接地壓力隨著 路面的高低不平和清掃車減振 彈簧 高度的變化而產生變化，而這種變化帶來的后果則是清掃效果 不穩定和加劇掃刷磨損。因此，清掃車生產企業有必要對清掃車掃刷的最佳接地壓力進行探討，并 設計能對掃刷接地壓力進行自動調整的清掃裝置，以期在達到最佳清掃效果的同時使掃刷磨損最少。 還有除塵系統研究：除塵系統的優劣，影響到清掃車的二次排放。清掃車的除塵分為濕式除塵和干 式除塵，其中濕式除塵又可分為噴水除塵和循環水除塵。 4 風道關鍵技術研究 掃路機風道 的設計如何，嚴重影響到清掃車的吸塵能力和功率利用率。掃路機的風道型式只有帶 反吹風的風道和不帶反吹風的風道兩種，但形狀各異。風道形狀、是否帶
7、反吹風以及反吹風風量占風 機風量的比例大小都會對清掃車的氣流阻力產生影響。這種氣流阻力的影響，將使 風機 的全壓和風量 產生變化。在清掃車的設計中，若風道設計不合適，氣流阻力大，為使 掃路機吸嘴處和吸管中能達到一 定的風量，就必須使 風機 轉速更高或采用更大風量的 風機 ，這樣，就必然會增大 風機 的功率，降低清 掃車的功率利用率，加大油耗。為此，必須對清掃車的風道系統進行試驗研究，確定清掃車風道形狀 對氣流阻力產生影響的阻力系數，確定反吹風風道對產生的阻力的大小以及其阻力對 風機 風量的影 響。只有這樣，才能設計出清掃效果好、氣流阻力小、功率利用率高的風道系統。 5 液壓系統關鍵技術研究 液
8、壓系統是清掃車的重要組成部分，完成清掃車作業過程中大量的動作，液壓系統的工作狀況直 接影響整車的性能，下面詳細介紹液壓系統完成的功能：完成盤刷的外伸和下降，使其接觸路面進行清掃作業；完成盤刷的收起使其恢復行使?fàn)顟B(tài)；完 成盤刷的旋轉作業；擺動油缸驅動滾刷的左向和右向斜置；滾刷的旋轉；護欄清洗裝置的外伸收回與 旋轉；垃圾箱的舉升降落和傾斜。 6 易磨損零部件關鍵 技術研究 清掃車的易磨損零部件主要有：掃刷、吸管、 風機 、吸嘴、風道等。清掃車零部件的耐磨性直接 影響到清掃車的使用成本，特別是掃刷是否耐磨對清掃車的使用成本影響最大?？梢哉f，掃刷磨損是 目前我國清掃車磨損問題中最嚴重的。提高清掃車零部
9、件耐磨性是提高其可靠性的直接有效的方法之 一，所以清掃車生產企業應對如何提高零部件的耐磨性引起高度重視。 sweeper key technology research In our country, as a result of the development of clean vehicles is shorter, the use of the small number of research and development personnel is limited, there is no specialized research institutions to study, so t
10、he lack of clean vehicle technologies major study of the key components, in order to enhance the sweeping and pure suction sweepers ability to design, to be its main components - cleaning systems, fans, air duct system and dust removal systems, as well as wear parts, such as a pilot study to improve
11、 the cleaning of the theory of the level of car design. 1 strengthen the sweeper dedicated fan of the key technologies Fan is a very important cleaning car parts, fan is the heart of dust sweeper parts, large air volume and air pressure is a reliable guarantee for high efficiency dust collection, we
12、 must choose high-performance centrifugal fan, as the sweeper operating condition instability, so in the selection of fans must have a certain margin in order to ensure that cleaning cars in a variety of road dust to achieve perfect results, due to space restrictions layout fans as far as possible,
13、compact appearance, while reducing noise when the fan is to choose one of the important factors to consider. Chinas clean car fan and have a wide gap between the developed countries, at present, our country clean cars fan most common fan or general fan of the system fan. As the general fan is a gene
14、ral-purpose and design of ventilation, and its size, resistance to abrasion, dust and so can not meet the cleaning ability of the poor condition of vehicles requested. It can be said that Chinas use of clean vehicles fan has significantly affected the performance of the sweeper. Therefore, the clean
15、-up car production enterprises should be strengthened sweeper dedicated fan of research, from the fan blade shape, blade material, and out of shape and location of outlet, such as processing technology to explore the design of small and large air volume, low noise, wear-resistant the fan. 2 The key
16、technology compressed air systems research Compressed air system is operating power sweeper an important component of the compressed air system is provided by the chassis engine cylinder of compressed air-driven action is scheduled to have completed the following functions: regulation of the pressur
17、e plate grounding brush, brush on the disk buffer to protect the role of when the ground will be raised up homeopathy, pressure regulating indoor driving completed upgrade at either end of a cylinder, the other end hanging in the frame, the manipulation of electronic control system to enable the com
18、pletion of the cylinder-led take-off and landing action to enhance the cylinder pressure can also adjust the ground so that 20o arc and ground contact. Enhance the hydraulic damping cylinder to cylinder to ensure contact with the ground and has always been pressure on the same ground, but also playe
19、d the role of damping the buffer to ensure that the impact from. suction suction cylinder can be up front will be large garbage inhalation, in the start or stop smoking when I upgrade will enhance the cylinder or to the ground. 3 key technology research Dust collection system, including disk cleanin
20、g brush device devices, suction devices, and some, such as dust collection box, which is a key component sweeper. Plate bears a brush cleaning device and collection and separation barrier near the angle with the task of garbage, brush and set it by the frame, oil motors, the arm body, the fuel tank
21、and frame, steel body and tailgate and drive wheel institutions. device is a large area on the highway in central road sweeping and refuse collection will be near to the suction, which, casing, oil motors, oscillating cylinder, the fuel tank and upgrade the stent, such as rotating parts. Suction dev
22、ice to suction through the region refuse suction pipe by the inhalation of harmful dust box, mainly by suction, hoses, frame, support vehicle, enhance suction cylinder, suction cylinder composed of. Dust box: it is a sweeping settlement of refuse collection trucks transport storage containers, dust
23、door open and the dumping of garbage by the chassis engine drives the hydraulic power output pump power, in the dust collection box impact plate, baffle, the rear there is a rectangular wire strainer, which increased the flow of plate collision effects, easy to refuse settlement isolated from the ai
24、rstream. So the pressure of another grounding brush size, not only affects the cleaning effectiveness of cleaning cars, but also for sweeping brush wear also have a significant impact. Chinas clean sweep vehicles grounding brush pressure cleaning truck operators from manually adjusted, under normal
25、circumstances, the operator only up to a sweeping brush on the ground when the pressure to adjust, and some only a few days or even ground pressure sweeping brush another period of adjustment. So the pressure of such a grounding of the adjustment brush, so as to enable operation of the sweeper brush
26、 sweep the ground pressure and severe as the road sweeper damping spring changes in a high degree of change, and the consequences of this change is sweeping So the effect of instability and increased brush wear. Therefore, the cleaning vehicle manufacturers need to brush sweeper sweep the best groun
27、d to discuss the pressure and the design of grounding brush can sweep to automatically adjust the pressure of the cleaning device, with a view to achieve the best cleaning results at the same time so that at least sweeping brush wear . There are dust system: the advantages and disadvantages of dust
28、removal system, affect the secondary emission sweeper. Into the dust sweeper wet and dry dust removal, in which water can be divided into wet dust removal and recycling of water removal. 4 Key Technologies of duct Road sweeper design wind Road, seriously affecting the cleaning ability of cleaning ca
29、rs and power utilization. So the way of air duct machine only with the anti-hair type of the air duct and without anti-air duct of the two types of hair, but different shape. Duct shape, whether or not with anti-hair-and anti-hair-style accounts for the ratio of air volume fan size sweeper will have
30、 an impact on the flow resistance. The effects of air resistance that will make fans of the whole amount of pressure and wind changes. In the design of car cleaning, if the design inappropriate for wind, air resistance, in order for the road sweeper nozzle and the straw in the wind to reach a certai
31、n volume, it is necessary to enable the fan speed higher or greater air volume of fan, This will inevitably increase the fan power, the power to reduce the utilization of clean vehicles, increased fuel consumption. To this end, the need for air duct cleaning system cars to carry out pilot studies to
32、 determine the shape of air duct cleaning truck to have an impact on air flow resistance of the drag coefficient to determine the anti-hair duct to generate the size of the resistance and its resistance to the fans of the impact of air volume. Only in this way can the design of effective cleaning, f
33、low resistance small, the utilization of high-power air duct system. 5 Key Technologies of the hydraulic system Sweeper hydraulic system is an important component of the operation to complete the process of cleaning a large number of car movements, the hydraulic system of the working conditions of a
34、 direct impact on vehicle performance, the following details to complete the function of the hydraulic system: the completion of the outer disk brush stretch and fall so that it contacts the road surface for cleaning operations; complete set brush away to resume the exercise of the state; complete s
35、et of rotating brushes operations; swing tanks drive to the left and right home syncline; rotation; cleaning device barrier recovery and rotating outriggers; litter and tilt of the lift landing. 6 parts easy to wear the key technology research Easy clean-up cars and wear parts are: sweeping brush, s
36、traw, fan, nozzle, such as air duct. Cleaning car parts and components directly affects the wear resistance of the clean-up costs of car use, especially wear-resistant sweeping brush is used to clean cars cost the most. It can be said that sweeping brush wear is the wear and tear our country clean cars in the most serious problem. Cleaning car parts and components to improve wear resistance is to increase the reliability of one of direct and effective way, so clean-up on how to deal with car manufacturers to improve the wear resistance of components a high degree of attention.
清掃車的關鍵技術研究環保機械課程畢業設計外文文獻翻譯@中英文翻譯@外文翻譯
