高速帶式輸送機的設計_外文翻譯
《高速帶式輸送機的設計_外文翻譯》由會員分享,可在線閱讀,更多相關《高速帶式輸送機的設計_外文翻譯(28頁珍藏版)》請?jiān)谘b配圖網上搜索。
1、附件Aesign of High Speed Belt ConveyorsG. Lodewijks, The Netherlands.SUMMARYThis paper discusses aspects of high-speed belt conveyor design. The capacity of a belt conveyor is determined by the belt speed given a belt width and troughing angle. Belt speed selection however is limited by practical cons
2、iderations, which are discussed in this paper. The belt speed also affects the performance of the conveyor belt, as for example its energy consumption and the stability of its running behavior. A method is discussed to evaluate the energy consumption of conveyor belts by using the loss factor of tra
3、nsport. With variation of the belt speed the safety factor requirements vary, which will affect the required belt strength. A new method to account for the effect of the belt speed on the safety factor is presented. Finally, the impact of the belt speed on component selection and on the design of tr
4、ansfer stations is discussed.1 INTRODUCTIONPast research has shown the economical feasibility of using narrower, faster running conveyor belts versus wider, slower running belts for long overland belt conveyor systems. See for example I-5. Today, conveyor belts running at speeds around 8 m/s are no
5、exceptions. However, velocities over 10 m/s up to 20 m/s are technically (dynamically) feasible and may also be economically feasible. In this paper belt speeds between the 10 and 20 m/s are classified as high. Belt speeds below the 10 m/s are classified as low.Using high belt speeds should never be
6、 a goal in itself. If using high belt speeds is not economically beneficial or if a safe and reliable operation is not ensured at a high belt speed then a lower belt speed should be selected.Selection of the belt speed is part of the total design process. The optimum belt conveyor design is determin
7、ed by static or steady state design methods. In these methods the belt is assumed to be a rigid, inelastic body. This enables quantification of the steady-state operation of the belt conveyor and determination of the size of conveyor components. The specification of the steady-state operation includ
8、es a quantification of the steady-state running belt tensions and power consumption for all material loading and relevant ambient conditions. It should be realized that finding the optimum design is not a one-time effort but an iterative process 6.Design fine-tuning, determination of the optimum sta
9、rting and stopping procedures, including determination of the required control algorithms, and determination of the settings and sizes of conveyor components such as drives, brakes and flywheels, are determined by dynamic design methods. In these design methods, also referred to as dynamic analyses,
10、 the belt is assumed to be a three-dimensional (visco-) elastic body. A three dimensional wave theory should be used to study time dependent transmission of large local force and displacement disturbances along the belt 7. In this theory the belt is divided into a series of finite elements. The fini
11、te elements incorporate (visco-) elastic springs and masses. The constitutive characteristics of the finite elements must represent the rheological characteristics of the belt. Dynamic analysis produces the belt tension and power consumption during non-stationary operation, like starting and stoppin
12、g, of the belt conveyor.This paper discusses the design of high belt-speed conveyors, in particular the impact of using high belt speeds on the performance of the conveyor belt in terms of energy consumption and safety factor requirements. Using high belt speeds also requires high reliability of con
13、veyor components such as idlers to achieve an acceptable component life. Another important aspect of high-speed belt conveyor design is the design of efficient feeding and discharge arrangements. These aspects will be discussed briefly.2 BELTSPEED2.1 BELT SPEED SELECTIONThe lowest overall belt conve
14、yor cost occur in the range of belt widths of 0.6 to 1.0 m 2. The required conveying capacity can be reached by selection of a belt width in this range and selecting whatever belt speed is required to achieve the required flow rate. Figure 1 shows an example of combinations of belt speed and belt wi
15、dth to achieve Specific conveyor capacities. In this example it is assumed that the bulk density is 850 kg/m3 (coal) and that the trough angle and the surcharge angle are 35 and 20 respectively.Figure 1: Belt width versus belt speed for different capacities.Belt speed selection is however limited by
16、 practical considerations. A first aspect is the troughability of the belt. In Figure 1 there is no relation with the required belt strength (rating), which partly depends on the conveyor length and elevation. The combination of belt width and strength must be chosen such that good troughability of
17、the belt is ensured. If the troughability is not sufficient then the belt will not track properly. This will result in unstable running behavior of the belt, in particular at high belt speeds, which is not acceptable. Normally, belt manufacturers expect a sufficiently straight run if approximately 4
18、0% of the belt width when running empty, makes contact with the carrying idlers. Approximately 10% should make tangential contact with the center idler roll.A second aspect is the speed of the air relative to the speed of the bulk solid material on the belt (relative airspeed). If the relative airsp
19、eed exceeds certain limits then dust will develop. This is in particular a potential problem in mine shafts where a downward airflow is maintained for ventilation purposes. The limit in relative airspeed depends on ambient conditions and bulk material characteristics.A third aspect is the noise gene
20、rated by the belt conveyor system. Noise levels generally increase with increasing belt speed. In residential areas noise levels are restricted to for example 65 dB. Although noise levels are greatly affected by the design of the conveyor support structure and conveyor covers, this may be a limiting
21、 factor in selecting the belt speed.2.2 BELT SPEED VARIATIONThe energy consumption of belt conveyor systems varies with variation of the belt speed, as will be shown in Section 3. The belt velocity can be adjusted with bulk material flow supplied at the loading point to save energy. If the belt is o
22、perating at full tonnage then it should run at the high (design) belt speed. The belt speed can be adjusted (decreased) to the actual material (volume) flow supplied at the loading point. This will maintain a constant filling of the belt trough and a constant bulk material load on the belt. A consta
23、nt filling of the belt trough yields an optimum loading-ratio, and lower energy consumption per unit of conveyed material may be expected. The reduction in energy consumption will be at least 10% for systems where the belt speed is varied compared to systems where the belt speed is kept constant 8.V
24、arying the belt speed with supplied bulk material flow has the following advantages: Less belt wear at the loading areas Lower noise emission Improved operating behavior as a result of better belt alignment and the avoidance of belt lifting in concave curve by reducing belt tensionsDrawbacks include
25、: Investment cost for controllability of the drive and brake systems Variation of discharge parabola with belt speed variation Control system required for controlling individual conveyors in a conveyor system Constant high belt pre-tension Constant high bulk material load on the idler rollsAn analys
26、is should be made of the expected energy savings to determine whether it is worth the effort of installing a more expensive, more complex conveyor system.3 ENERGY CONSUMPTIONClients may request a specification of the energy consumption of a conveyor system, for example quantified in terms of maximum
27、 kW-hr/ton/km, to transport the bulk solid material at the design specifications over the projected route. For long overland systems, the energy consumption is mainly determined by the work done to overcome the indentation rolling resistance 9. This is the resistance that the belt experiences due to
28、 the visco-elastic (time delayed) response of the rubber belt cover to the indentation of the idler roll. For in-plant belt conveyors, work done to overcome side resistances that occur mainly in the loading area also affects the energy consumption. Side resistances include the resistance due to fric
29、tion on the side walls of the chute and resistance that occurs due to acceleration of the material at the loading point.The required drive power of a belt conveyor is determined by the sum of the total frictional resistances and the total material lift. The frictional resistances include hysteresis
30、losses, which can be considered as viscous (velocity dependent) friction components. It does not suffice to look just at the maximum required drive power to evaluate whether or not the energy consumption of a conveyor system is reasonable. The best method to compare the energy consumption of differe
31、nt transport systems is to compare their transport efficiencies.3.1 TRANSPORT EFFICIENCYThere are a number of methods to compare transport efficiencies. The first and most widely applied method is to compare equivalent friction factors such as the DIN f factor. An advantage of using an equivalent fr
32、iction factor is that it can also be determined for an empty belt. A drawback of using an equivalent friction factor is that it is not a pure efficiency number. It takes into account the mass of the belt, reduced mass of the rollers and the mass of the transported material. In a pure efficiency numb
33、er, only the mass of the transported material is taken into account.The second method is to compare transportation cost, either in kW-hr/ton/km or in $/ton/km. The advantage of using the transportation cost is that this number is widely used for management purposes. The disadvantage of using the tra
34、nsportation cost is that it does not directly reflect the efficiency of a system.The third and most pure method is to compare the loss factor of transport 10. The loss factor of transport is the ratio between the drive power required to overcome frictional losses (neglecting drive efficiency and pow
35、er loss/gain required to raise/lower the bulk material) and the transport work. The transport work is defined as the multiplication of the total transported quantity of bulk material and the average transport velocity. The advantage of using loss factors of transport is that they can be compared to
36、loss factors of transport of other means of transport, like trucks and trains. The disadvantage is that the loss factor of transport depends on the transported quantity of material, which implies that it can not be determined for an empty belt conveyor.The following are loss factors of transport for
37、 a number of transport systems to illustrate the concept:Continuous transport: Slurry transport around 0.01 Belt conveyors between 0.01 and 0.1 Vibratory feeders between 0.1 and 1 Pneumatic conveyors around 1 0 Discontinuous transport: Ship between 0.001 and 0.01 Train around 0.01 Truck between 0.05
38、 and 0.1 3.2 INDENTATION ROLLING RESISTANCEFor long overland systems, the energy consumption is mainly determined by the work done to overcome the indentation rolling resistance. Idler rolls are made of a relatively hard material like steel or aluminum whereas conveyor belt covers are made of much s
39、ofter materials like rubber or PVC. The rolls therefore indent the belts bottom-cover when the belt moves over the idler rolls, due to the weight of the belt and bulk material on the belt. The recovery of the compressed parts of the belts bottom cover will take some time due to its visco-elastic (ti
40、me dependent) properties. The time delay in the recovery of the belts bottom cover results in an asymmetrical stress distribution between the belt and the rolls, see Figure 2. This yields a resultant resistance force called the indentation rolling resistance force. The magnitude of this force depend
41、s on the visco-elastic properties of the cover material, the radius of the idler roll, the vertical force due to the weight of the belt and the bulk solid material, and the radius of curvature of the belt in curves in the vertical plane.Figure 2: Asymmetric stress distribution between belt and roll
42、7.It is important to know how the indentation rolling resistance depends on the belt velocity to enable selection of a proper belt velocity, 11.Figure 3: Loss factor (tanb) of typical cover rubber 7Firstly, the indentation rolling resistance depends on the vertical load on the belt, which is the sum
43、 of the belt and the bulk material weight. If the vertical load on the belt decreases with a factor 2 then the indentation rolling resistance decreases with a factor 2.52 (2 4/3). The bulk load decreases with increasing belt speed assuming a constant capacity. Therefore, the indentation rolling resi
44、stance decreases more than proportionally with increasing belt speed.Secondly, the indentation rolling resistance depends on the size of the idler rolls. If the roll diameter increases with a factor 2 then the indentation rolling resistance decreases with a factor 1.58 (2 2/3). In general the idler
45、roll diameter increases with increasing belt speed to limit the bearing rpms to maintain acceptable idler life. In that case the indentation rolling resistance decreases with increasing belt speed.Thirdly, the indentation rolling resistance depends on the visco-elastic properties of the belts cover
46、material. These properties depend on the deformation rate, see Figure 3. The deformation rate in its turn depends on the size of the deformation area in the belts bottom cover (depending on belt and bulk load) and on the belt speed. In general the indentation rolling resistance increases with increa
47、sing deformation rate (and thus belt speed), but only to a relatively small account.Fourthly, the indentation rolling resistance depends on the belts bottom cover thickness. If the bottom cover thickness increases with a factor 2 then the indentation rolling resistance increases with a factor 1.26 (
48、2 1/3). if a bottom cover is increased to account for an increase in belt wear with increasing belt speed, then the indentation rolling resistance increases as well.It should be realized that the indentation rolling resistance, although important, is not the only velocity dependent resistance. The r
49、olling resistance of the idler rolls for example depends on the vertical load as well as on their rotational speed. The effect of the vertical load, which directly depends on the belt speed, is large. The effect of the rotational speed is much smaller. Another resistance occurs due to acceleration o
50、f the bulk solid material at the loading point. This resistance increases quadratically with an increase in belt speed assuming that the bulk material falls straight onto the belt. This will affect smaller, in plant belt conveyors in particular.EXAMPLETo illustrate the concept discussed above lets c
51、onsider a 6 km long conveyor belt with a capacity of 5000 TPH. The trough angle, the surcharge angle and the bulk density are again taken 35, 20 and 850 kg/m3 respectively. Figure 4 shows the required belt speed as a function of the belt width to achieve the required capacity of 5000 TPH. This figur
52、e is somewhat similar to Figure 1.Figure 4The figures 5 and 6 show the required belt strength and the required drive power as a function of the belt speed. The required belt strength decreases and the required drive power slowly increases with increasing belt speed as can be seen in those figures. F
53、igure 7 shows the loss factor of transport and the DIN f factor versus belt speed. The loss factor of transport is always higher than the DIN f factor because the DIN f factor takes the mass of the belt into account (in the denominator) whereas the loss factor of transport only accounts for the mass
54、 of the bulk solid material. Intuitively, it may be expected that there will be an economically optimum belt speed in the high belt speed range. The determination of the optimum belt speed however, requires more information and is beyond the scope of this paper.Figure 5Figure 6Figure 73.3 RUBBER COM
55、POUNDSThe indentation rolling resistance depends on the visco-elastic properties of the belts bottom cover as discussed in the preceding section. This implies that the rolling resistance can be decreased by selecting a special low indentation rolling resistance (rubber) compound that is available on
56、 the market today. A small premium has to be paid for this special compound, but costs can be limited by applying it for the bottom cover only and using a normal wear-resistant compound for the carrying top cover. In that case turnovers are required to fully use the energy saving function of the bot
57、tom compound.A Quantitative indication of the level of indentation rolling resistance is the indentation rolling resistance indicator tan/E 1/3, where tan is the loss angle and E the storage modulus of the compound. Compounds with a reasonable indentation rolling resistance performance have indicato
58、rs below 0.1. Figure 8 shows these indicators for typical medium to good performing rubbers. As can be seen in that figure, the choice for a specific rubber compound affects the energy consumption of the belt conveyor, in particular as a function of the ambient temperature.One comment (warning) must
59、 be made. A special belt with low indentation rolling resistance compound should never be selected if only one conveyor belt manufacturer offers it. In that case the conveyor system can only perform in accordance with its design specifications when that specific belt is used. It is much better, also
60、 cost wise, to specify the upper limit of the resistance indicator as given above that can be met by more than one conveyor belt manufacturer.Figure 8: Indentation rolling resistance indicators for fourdifferent rubbers as a function of temperature.4. SAFETY FACTOR REQUIREMENTSFor design purposes, s
61、tandards like DIN 22101, ISO 5048 and CEMA provide safety factors (SF) that limit the permissible belt loads. Two types of safety factors can be distinguished: safety factors on the steady-state running tensions and safety factors on the non-stationary tensions. In general the safety factor on the s
62、teady-state running tension is based on:(1) Stationary (full and empty, summer and winter) and non-stationary belt tensions(2) Belt tensions from extra resistances and deformations in horizontal and vertical curves, troughing transitions, belt turnovers, on pulleys etc.(3) Belt conveyor system maint
63、enance(4) Belt conveyor system operational data including hours per day, days per year and years of service(5) Belt splice design and fatigue characteristics including those of the belt tensile carrying member (steel cords or fabric) and the rubber(6) Splice kit storage and handling.All these six it
64、ems should be taken into account when determining the safety factor.standards like the DIN standard base the recommended safety factor on reduction factors. DIN 22101 uses three reduction factors. The first (r0) generally accounts for the reduction of the strength of the belt (splices) due to fatigu
65、e. The second (r1) accounts for the extra forces that act on the belt in transition zones and on pulleys etc. The third (r2) accounts for the extra dynamic stresses in the belt during starting and stopping. The required minimum safety factor can be calculated as follows:SF=1/(1-(r0+r1+r2) (1)The DIN standard also gives values for the three reduction factors. For example, for a steel cord conveyor belt under normal operational conditions the values are as follows: r00.665, r10.15, r20.06, which yields a safety factor SF8.Although much can
- 溫馨提示:
1: 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
2: 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
3.本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
5. 裝配圖網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。