帶輪的沖壓工藝與模具設計【三維UG工件圖】【含51張圖紙】

喜歡就充值下載吧。資源目錄里展示的全都有，下載后全都有請放心下載，原稿可自行編輯修改=【QQ：1304139763可咨詢交流】喜歡就充值下載吧。喜歡就充值下載吧。資源目錄里展示的全都有，下載后全都有請放心下載，原稿可自行編輯修改=【QQ：1304139763可咨詢交流】喜歡就充值下載吧。喜歡就充值下載吧。資源目錄里展示的全都有，下載后全都有請放心下載，原稿可自行編輯修改=【QQ：1304139763可咨詢交流】喜歡就充值下載吧。 山東建筑大學畢業設計說明書目 錄 摘 要ABSTRACT1 前 言1.1 選題背景11.2課題設計思路11.3設計過程中的難點22 工藝分析及計算2.1工件的基本信息分析32.2工藝分析32.2.1工序計算 42.2.2計算毛坯直徑52.2.3工藝方案的確定72.2.4排樣及搭邊82.3工藝計算92.3.1工藝力的計算及壓力機的選擇92.3.2主要工作部分尺寸計算123模具設計3.1落料拉深復合模的設計153.1.1落料拉深復合模結構設計153.1.2落料拉深復合模主要零件設計163.2沖孔模設計193.2.1沖孔模結構設計193.2.2沖孔模主要零件設計203.3翻邊模設計223.3.1翻邊模結構設計223.3.2翻邊模主要零件設計223.4切邊整形復合模的設計243.4.1切邊整形復合模結構設計243.4.2切邊整形復合模主要零件設計253.5擴口壓平復合模的設計273.5.1擴口壓平復合模結構設計273.5.2擴口壓平復合模主要零件設計274 結 論31謝 辭32參考文獻33 IV摘 要 本文是對拉深件進行工藝分析及模具設計。該工件是一個圓筒形拉深件，另外該工件的底部帶有通孔，需進行沖孔翻邊，雖然形狀不太復雜但肯定不能一次成形。通過對零件各部分進行計算分析后才能最終確定加工工序。工件整個成形過程所涉及的工序有：落料、拉深、沖孔、翻邊等四步。通過計算分析得翻邊能一次成形，所以不需進行預拉深，而計算可知拉深可一次成形，所以確定最終工藝方案為：落料與拉深復合，沖孔、翻邊復合。在確定工藝方案的基礎上對主要模具進行設計，分析工件成型過程，設計模具的結構并畫出模具裝配圖及零件圖。在本次設計中主要對落料拉深復合模以及沖孔、翻邊模進行設計。關鍵詞：拉深；落料拉深復合模；ABSTRACTThe thesis is focus on the process analysis and mold design of the drawing.The workpiece we design is a cylinder-shaped drawing parts,which has a hole at the bottom.The workpiece should be punched and flanged.Although the shape is not very complex,it couldnt be shaped by one step.We can determine the processing by analyzing the parts of the workpiece.The process include several steps:blanking,drawing,punching and flanging.By analysis,we know that the flanging can be finished by one step.There should not be a pre-drawing.However,the drawing can be achieved easily.Therefore,the final process is compounding the blanking with the drawing, the punching die and flanging die.Besides,we should design the main die,analyse the process,design the structure of the die and draw the assembly and workpiece picutures.In this graduation project,we mainly design the blanking drawing die, the punching die and flanging die.Key words: drawing die； blanking drawing compound die；山東建筑大學畢業設計說明書- 1 -