購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
河南機電高等?？茖W(xué)校畢業設計說明書
臺面框塑料注塑模
摘 要
本設計題目為臺面柜的注射模具設計，體現了注射模具的設計要求、內容及方向，有一定的設計意義。通過對該零件模具的設計，進一步加強了設計者注射模具設計的基礎知識，為設計更復雜的注射模具做好了鋪墊和吸取了更深刻的經驗。
本設計運用典型的注射模具設計的基礎知識，首先分析了塑料的性能要求，為選取模具的類型做好了準備；然后計算了塑件的脫模力，便于確定注射機；因該模具采用倒裝結構，故選用了加長噴嘴進行注塑；最后分析了塑件的特征，確定模具的設計參數、設計要點及頂出裝置的選取。
本設計采用了多頂桿脫模機構，保證了制件順利脫模。
關鍵詞：臺面柜 注射模具 斜頂桿抽芯 脫模 塑件
Abstract
Summary of the design theme of the bottom bed cabinet injection mold design reflects the injection mold design, content and direction. is of a certain significance. Through parts mold design, further strengthening the injection mold designers basis for the design of knowledge, for the design of more complex injection mold has laid a good groundwork and learned a more profound experience.
The use of the typical design of injection mold design of the basic knowledge, the first analysis of the properties of plastic, To select the type of mold well prepared; Then calculate the plastic parts of the ejection force, to facilitate the identification injection; Because of the die using upside-down charging architecture ,so preferred the lengthen muzzle to inject. Finally, the plastic parts of the characteristics of the die to determine design parameters and design features of the device from the top selection.
This was designed with ramps mandrel ejection mechanism, assurance the lastics combinations to mould unloading favorably.
Keywords : bottom bed cabinet ，injection mold， stem from the core-pulling pieces of molding ，demolding, plastic part.
2