3919 轉速器盤加工工藝及關鍵工序工裝設計
3919 轉速器盤加工工藝及關鍵工序工裝設計,轉速,加工,工藝,關鍵,癥結,樞紐,工序,工裝,設計
機床生產率計算卡圖號 毛坯種類 鑄件名稱 轉速器盤 毛坯重量被加工零件材料 HT200 硬度 175~255HBS工序名稱 鉆 Φ9.8 孔 工序號 工時/min序號 工步名稱 工作行程/mm 切速/(m/min) 進給量/(mm/r) 進給量/(mm/min) 工進時間輔助時間1 安裝工件 0.72 工件定位、夾緊 0.053 鉆頭快進 90 5000 0.034 鉆頭工進 17 6 0.43 84 0.365 死擋鐵停留 0.016 鉆頭快退 107 5000 0.0367 工件松開 0.058 卸下工件 0.7累計 0.036 1.576單件總工時 1.612機床生產率 37.22(件/h)理論生產率 25.64(件/h)備注1.一次安裝加工一個工件2.本機床裝卸工件時間取 1.4min負荷率 68.89%南京理工大學泰州科技學院學生畢業設計(論文)中期檢查表學生姓名 徐東青 學 號 0501510144 指導教師 龔光容課題名稱 轉速器盤加工工藝及關鍵工序工裝設計難易程度 偏難 適中 √ 偏易選題情況工作量 較大 合理 √ 較小任務書 有 √ 無開題報告 有 √ 無符合規范化 的要求外文翻譯質量 優 良 中 √ 差學習態度、出勤情況 好 一般 √ 差工作進度 快 按計劃進行 慢 √中期工作匯報及解答問題情況優 良 中 √ 差中期成績?cè)u(píng)定:中所在專業意見:學習態度、出勤情況一般,工作進度慢,階段成果不明顯。負責人: 年 月 日 南京理工大學泰州科技學院畢業設計(論文)任務書系 部 : 機械工程系專 業 : 機械工程及自動化學 生 姓 名: 徐東青學 號:0501510144設 計 (論 文 )題 目 : 轉速器盤加工工藝及關鍵工序工裝設計起 迄 日 期 : 2008 年 3 月 09 日 ~ 6 月 14 日設計 (論文 )地點 : 南京理工大學泰州科技學院指 導 教 師 : 龔光容 教授專 業 負 責 人 : 龔光容發任務書日期: 2009 年 2 月 26 日任務書填寫要求1.畢業設計(論文)任務書由指導教師根據各課題的具體情況填寫,經學生所在專業的負責人審查、系部領導簽字后生效。此任務書應在第七學期結束前填好并發給學生;2.任務書內容必須用黑墨水筆工整書寫或按教務處統一設計的電子文檔標準格式(可從教務處網頁上下載)打印,不得隨便涂改或潦草書寫,禁止打印在其它紙上后剪貼;3.任務書內填寫的內容,必須和學生畢業設計(論文)完成的情況相一致,若有變更,應當經過所在專業及系部主管領導審批后方可重新填寫;4.任務書內有關“系部” 、 “專業”等名稱的填寫,應寫中文全稱,不能寫數字代碼。學生的“學號”要寫全號;5.任務書內“主要參考文獻”的填寫,應按照國標 GB 7714—2005《文后參考文獻著錄規則》的要求書寫,不能有隨意性;6.有關年月日等日期的填寫,應當按照國標 GB/T 7408—2005《數據元和交換格式、信息交換、日期和時間表示法》規定的要求,一律用阿拉伯?dāng)?shù)字書寫。如“2008 年 3 月 15 日”或“2008-03-15”。畢 業 設 計(論 文)任 務 書1.本畢業設計(論文)課題應達到的目的:轉速器盤是某企業產品中的關鍵零件之一,生產量比較大。為了保證產品質量,提高加工效率,需要對其加工工藝進行優化設計,并在關鍵工序使用組合機床或?qū)S脵C(jī)床進行加工。本課題即以此為背景,要求學生根據企業生產需要和轉速器盤零件的加工要求,首先完成零件的加工工藝規程設計,在此基礎之上,選擇其關鍵工序之一進行專用夾具及加工用組合機床設計,并完成必要的設計計算。通過這樣一個典型環節綜合訓練,達到綜合訓練學生運用所學知識,解決工程實際問題的能力。2.本畢業設計(論文)課題任務的內容和要求(包括原始數據、技術要求、工作要求等):本課題要求學生在對轉速器盤的加工要求、零件的結構工藝性進行認真分析的基礎上,首先對零件的加工工藝規程做出優化設計,并對其關鍵工序之一進行專用夾具及加工用組合機床設計。具體任務及要求如下:(1)調查研究、查閱及翻譯文獻資料,撰寫開題報告;(2)轉速器盤加工要求、零件的結構工藝性分析;(3)轉速器盤加工工藝規程設計;(4)轉速器盤關鍵工序的專用夾具設計;(5)轉速器盤關鍵工序的組合機床設計;(6)必要的設計計算與分析;(7)文檔整理、撰寫畢業設計說明書及使用說明書。設計技術要求包括:(1)生產綱領 50000 件/年(2)夾具采用液壓驅動(3)組合機床采用液壓滑臺(4)每次加工一個零件畢 業 設 計(論 文)任 務 書3.對本畢業設計(論文)課題成果的要求〔包括畢業設計論文、圖表、實物樣品等〕:(1)開題報告、文獻綜述、資料翻譯;(2)轉速器盤加工工藝過程綜合卡及各工序工序卡;(3)轉速器盤零件圖及夾具裝配圖;(4)組合機床設計資料(三圖一卡) ;(5)畢業設計說明書。 4.主要參考文獻:[1] 裘愉弢主編. 組合機床[M]. 第 1 版.北京:機械工業出版社,1995.[2] 金振華主編.組合機床及其調整與使用[M]. 第 1 版.北京:機械工業出版社,1990.[3] 沈延山.生產實習與組合機床設計[D].第 1 版.大連:大連理工大學出版社,1989.[4] 上海市大專院校機械制造工藝學協作組編著.機械制造工藝學[M] (修訂版).福建科學技術出版社,1996.[5] 王華坤,范元?jiǎng)拙?機械設計基礎[M].北京:兵器工業出版社,2000.[6] 馮辛安等編.機械制造裝備設計[M]. 北京:機械工業出版社,1998.[7] 陳日曜主編.金屬切削原理[M]. 第 2 版.北京:機械工業出版社,1992.[8] 方子良等編.機械制造技術基礎[M].上海:上海交通大學出版社,2004.[9] 劉秋生,李忠文主編.液壓傳動與控制[M].北京:宇航出版社,1994.[10] 陳于萍,周兆元等.互換性與測量技術基礎[M]. 第 2 版.北京:機械工業出版社,2005.[11] 東北重型機械學院等合編.機床夾具設計手冊[M].上海:上??茖W(xué)技術出版社,1979.[12]《機械設計手冊》聯合編寫組. 機械設計手冊[M]. 第 2 版.北京:機械工業出版社,1987.畢 業 設 計(論 文)任 務 書5.本畢業設計(論文)課題工作進度計劃:起 迄 日 期 工 作 內 容2009 年3 月 09 日 ~ 3 月 15 日3 月 16 日 ~ 3 月 29 日3 月 30 日 ~ 4 月 19 日4 月 20 日 ~ 5 月 03 日5 月 04 日 ~ 5 月 31 日6 月 01 日 ~ 6 月 07 日6 月 08 日 ~ 6 月 14 日熟悉畢業設計要求。查閱資料,完成外文資料翻譯工作撰寫開題報告及文獻綜述轉速器盤加工工藝規程設計(至少提出 2 個方案,進行分析比較,最后決定一個較優的方案)夾具設計(至少提出 2 個方案,進行分析比較,最后決定一個較優的方案)組合機床設計(完成三圖一卡)文檔整理、撰寫畢業設計說明書。論文答辯所在專業審查意見:負責人: 2009 年 月 日系部意見:系部主任: 2009 年 月 日南京理工大學泰州科技學院畢業設計(論文)前期工作材料學 生 姓 名 : 徐東青 學 號: 0501510144系 部 : 機械工程系專 業 : 機械工程及自動化設計 (論 文 )題 目 : 轉速器盤加工工藝及關鍵工序工裝設計指 導 教 師 : 龔光容 教授材 料 目 錄序號 名 稱 數量 備 注1 畢業設計(論文)選題、審題表 12 畢業設計(論文)任務書 13 畢業設計(論文)開題報告〔含文獻綜述〕 14 畢業設計(論文)外文資料翻譯〔含原文〕 15 畢業設計(論文)中期檢查表 12009 年 6 月 南京理工大學泰州科技學院畢業設計(論文)外文資料翻譯系 部: 機械工程系 專 業: 機械工程及自動化 姓 名: 徐東青 學 號: 0501510144 外文出處: Electromechanical Integration and The Development of Technology Trends 附 件: 1.外文資料翻譯譯文;2.外文原文。 指導教師評語:簽名: 年 月 日附件 1:外文資料翻譯譯文機電一體化技術一、機電一體化技術發展歷程及其趨勢自電子技術一問世,電子技術與機械技術的結合就開始了,只是出現了半導體集成電路,尤其是出現了以微處理器為代表的大規模集成電路以后,機電一體化技術之后有了明顯進展,引起了人們的廣泛注意。(一)機電一體化的發展歷程1.數控機床的問世,寫下了機電一體化歷史的第一頁;2.微電子技術為機電一體化帶來勃勃生機; 3.可編程序控制器、電力電子等的發展為機電一體化提供了堅強基礎;4.激光技術、模糊技術、信息技術等新技術使機電一體化躍上新臺階。(二)機電一體化發展趨勢 1.光機電一體化。一般的機電一體化系統是由傳感系統、能源系統、信息處理系統、機械結構等部件組成的。因此,引進光學技術,實現光學技術的先天優點是能有效地改進機電一體化系統的傳感系統、能源(動力)系統和信息處理系統。光機電一體化是機電產品發展的重要趨勢。2.自律分配系統化——柔性化。未來的機電一體化產品,控制和執行系統有足夠的冗余度,有較強的柔性,能較好地應付突發事件,被設計成自律分配系統。在自律分配系統中,各個子系統是相互獨立工作的,子系統為總系統服務,同時具有本身的自律性,可根據不同的環境條件作出不同反應。其特點是子系統可產生本身的信息并附加所給信息,在總的前提下,具體行動是可以改變的。這樣,既明顯地增加了系統的適應能力(柔性),又不因某一子系統的故障而影響整個系統。3.全息系統化——智能化。今后的機電一體化產品全息特征越來越明顯,智能化水平越來越高。這主要收益于模糊技術、信息技術(尤其是軟件及芯片技術)的發展。除此之外,其系統的層次結構,也變簡單的從上到下的形勢而為復雜的、有較多冗余度的雙向聯系。4.生物一軟件化—仿生物系統化。今后的機電一體化裝置對信息的依賴性很大,并且往往在結構上是處于靜態時不穩定,但在動態(工作)時卻是穩定的。這有點類似于活的生物:當控制系統(大腦)停止工作時,生物便死亡,而當控制系統(大腦)工作時,生物就很有活力。仿生學研究領域中已發現的一些生物體優良的機構可為機電一體化產品提供新型機體,但如何使這些新型機體具有活的生命還有待于深入研究。這一研究領域稱為生物——軟件或生物——系統,而生物的特點是硬件(肌體)——軟件(大腦)一體,不可分割??磥?,機電一體化產品雖然有向生物系統化發展趨,但有一段漫長的道路要走。5.微型機電化——微型化。目前,利用半導體器件制造過程中的蝕刻技術,在實驗室中已制造出亞微米級的機械元件。當將這一成果用于實際產品時,就沒有必要區分機械部分和控制器了。屆時機械和電子完全可以融合,機體、執行機構、傳感器、CPU 等可集成在一起,體積很小,并組成一種自律元件。這種微型機械學是機電一體化的重要發展方向。二、典型的機電一體化產品機電一體化產品分系統(整機)和基礎元、部件兩大類。典型的機電一體化系統有:數控機床、機器人、汽車電子化產品、智能化儀器儀表、電子排版印刷系統、CAD/CAM 系統等。典型的機電一體化元、部件有:電力電子器件及裝置、可編程序控制器、模糊控制器、微型電機、傳感器、專用集成電路、伺服機構等。這些典型的機電一體化產品的技術現狀、發展趨勢、市場前景分析從略。三、我國發展機電一體化面臨的形勢和任務機電一體化工作主要包括兩個層次:一是用微電子技術改造傳統產業,其目的是節能、節材,提高工效,提高產品質量,把傳統工業的技術進步提高一步;二是開發自動化、數字化、智能化機電產品,促進產品的更新?lián)Q代。(一)我國機電一體化工作面臨的形勢1. 我國用微電子技術改造傳統工業的工作量大而廣,有難度。2. 我國用機電一體化技術加速產品更新?lián)Q代,提高市場占有率的呼聲高,有壓力。3. 我國用機電一體化產品取代技術含量和附加值低,耗能、耗水、耗材高、污染、擾民產品的責任重,有意義。在我國工業系統中,能耗、耗水大戶,對環境污染嚴重的企業還占相當大的比重。近年來我國的工業結構、產品結構雖然幾經調整,但由于多種原因,成效一直不夠明顯。這里面固然有上級領導部門的政出多門問題,有企業的故土難離,死守故業問題,但不可否認也有優化不出理想的產業,優選不出中意的產品問題。上佳的答案早就擺在了這些企業的面前,這就是發展機電一體化,開發和生產有關的機電一體化產品。機電一體化產品功能強、性能好、質量高、成本低,且具有柔性,可根據市場需要和用戶反映時產品結構和生產過程做必要的調整、改革,而無須改換設備。這是解決機電產品多品種、少批量生產的重要出路。同時,可為傳統的機械工業注入新鮮血液,帶來新的活力,把機械生產從繁重的體力勞動中解脫出來,實現文明生產。另外,從市場需求的角度看,由于我國研制、開發機電一體化產品的歷史不長,差距較大,許多產品的品種、數量、檔次、質量都不能滿足需求,每年進口量都比較大,因此亟需發展。(二) 我國機電一體化工作的任務我國在機電一體化方面的任務可以概括為兩句話:一句話是廣泛深入地用機電一體化技術改造傳統產業;另一句話是大張旗鼓地開發機電一體化產品,促進機電產品的更新?lián)Q代??偟哪康氖谴龠M(jìn)機電一體產業的形成、為我國產業結構和產品結構調整作貢獻。總之,機電一體化技術既是振興傳統機電工業的新鮮血液和源動力,又是開啟我國機電行業產品結構、產業結構調整大門的鑰匙。四、我國發展機電一體化的對策(一)加強統籌安排,協調發展計劃目前,我國從事機電一體化研究開發及生產的單位很多。各自都有一套自己的發展策略。各單位的計劃由于受各自立足點、著眼點的限制,難免只考慮局部利益,各主管部門的有關計劃和規劃,也有統一考慮不足,統籌安排不夠的問題,同時缺少綜觀全局的有權威性的發展計劃和戰略規劃。因此,建議各主管部門責成有關單位在進行深入調查研究、科學分析的基礎上,制定出統管全局的機電一體化研究、開發、生產計劃和規劃,避免開發上重復,生產上撞車。(二)強化行業管理,發揮協會作用目前,我國機電一體化較熱,而按目前的行業劃分方法和管理體制,政出多門是難哆的。因此,我國有必要明確一個機電一體化行業的統管機構,根據目前國家政治體制改革和經濟體制改革的精神,以及機電一體化行業特點,我們建議,盡快加強北京機電一體化協會的建設,賦予其行業管理職能。協會要進一步擴大領導機構——理事會的代表層面和復蓋面,要加強辦公室、秘書處的建設;要通過其精明干練的辦事機構、經濟實體,組織行業發展計劃、戰略規劃的擬制;指導行業布點布局的調整,進行發展突破口的選擇,抓好重點工程的試點和有關項目的發標、招標工作……(三)優化發展環境、增大支持力度優化發展環境指通過宣傳群眾,造成一種社會上下、企業內外都重視、支持機電一體化發展的氛圍,如盡快為外商到我國投資發展機電一體化產業提供方便;盡可能為興辦開發、生產機電一體化產品的高新技術企業開綠燈;盡力為開發、生產機電一體化產品調配好資源要素等。增大支持力度,在技術政策上,要嚴格限制耗電、耗水、耗材高的傳統產品的發展,對未采用機電一體化技術落后產品限制強制淘汰;大力提倡用機電一體化技術對傳統產業進行改造,對有關機電一體化技術對傳統產業乾地改造,對有關技術開發、應用項目優先立項、優先支持,對在技術開發、應用中做出貢獻的單位領導、科技人員進行表彰獎勵等。(四)突出發展重點,兼顧兩個層次機電一體化產業復蓋面非常廣,而我們的財力、人力和物力是有限的,因此我們?cè)谧C(jī)電一體化產業發展時不能面面俱到、平鋪直敘,而應分清主次,大膽取舍,有所為,有所不為。要注意抓兩個層次上的工作。第一個層次是面上的工作,即用電子信息技術對傳統產業進行改造,在傳統的機電設備上植入或嫁接上微電子(計算機)裝置,使機械和電子技術在淺層次上結合。第二個層次是提高工作,即在新產品設計之初,就把機械與電子統一起來進行考慮,使機械與電子密不可分,深度結合,生產出來的新產品起碼正做到機電一體化。結束語:本論文在各位老師的悉心指導和嚴格要求下已完成。在學習和生活期間,也始終感受著導師的精心指導和無私的關懷,我受益匪淺。在此向各位老師表示深深的感謝和崇高的敬意。不積跬步何以至千里,本設計能夠順利的完成,也歸功于各位任課老師的認真負責,使我能夠很好的掌握和運用專業知識,并在設計中得以體現。同時我在網上也搜集了不少資料,才使我的畢業論文工作順利完成。在此向?qū)W院工程系的全體老師表示由衷的謝意。附件 2:外文原文Electromechanical Integration1. electromechanical integration and the development of technology trends Since an electronic technology birth of electronic technology and mechanical technology integration began, only a semiconductor integrated circuit, particularly in a microprocessor representative of the large-scale integrated circuits for the future, “mechatronics, ” a technical after significant progress, and has attracted widespread attention. (A) mechanical-electrical integration, “the course of development 1. CNC machine tools come out, wrote “mechatronics, ” the first page of history; 2. Microelectronic technology, “mechatronics''bring a great vitality; 3. PLC, “Power Electronics” for the development of “mechatronics” provide a firm foundation; 4. Laser technology, fuzzy technology, information technology and other new technologies to “mechanical and electrical integration, ” a new and higher level. (B) mechanical-electrical integration, “the development trend 1. Integration of optical and electrical machinery. General mechanical and electrical integration system by sensing systems, energy systems, information processing systems, machinery, and other components of the structure. Therefore, the introduction of optical technology, the realization of the inherent advantages of optical technology is effective Improved mechanical-electrical integration system sensing system, energy (power) systems and information processing system. optical and electrical machinery integration is the development of mechanical and electrical products trend. 2. Systematic self-distribution - Flexible Future electromechanical integration products, and implementation of control systems are adequate “redundancy” and more “flexible” and can better deal with an emergency, is designed “self-distribution system.” Self-discipline in the distribution system, the various subsystems are independent of each other's work, the subsystem for system services, and has its own “self-discipline”, according to different environmental conditions react differently. Its characteristics are subsystem can generate its own information and additional information given in the overall premise, specific “action” can be changed. In this way, significantly increase the system's ability to adapt (flexible), not because of the failure of a subsystem of the whole system. 3. Holographic systematic - intelligent. Future integration of mechanical and electrical products, “holographic” features more and more obvious, more and more high-level intelligence. This is mainly revenues in the fuzzy technology, information technology (especially software and chip technology) development. In addition, the hierarchical structure of the system, a simple change of “top-down” situation is complex, there is much more two-way link redundancy. 4. “Of a software” of the - Biomimetic systematic. Future integration of electrical and mechanical devices on the dependence of great information, and often the structure is in a “static” instability, but in a dynamic (work) when is stable. This is a bit like living biological: When control system (the brain) to stop work, then of “Death”, and when control system (brain) work, the biological vitality. Bionics research in the field of a number of organisms have been found good institutions can provide products for the electrical and mechanical integration of the new body, but how to live with these new body of “Life” has to be in-depth study. This field of study referred to as “biological - Software” or “biological - System”, and biological characteristics of the hardware (body) - Software (brain) one and indivisible. It seems, electromechanical integration of the products although there are more systematic development, but there is a long way to go. 5. MEMS of - miniaturization. At present, the semiconductor devices used in the manufacturing process of etching technology, in the lab has produced sub-micron mechanical components. When will this result for the actual product, there is no need to distinguish between the mechanical part and controller. Will be completely mechanical and electronic “integration”, and the body, the Executive Body, sensors, such as CPU can be integrated with the size of a small, and the formation of a self-regulatory components. This micro-mechanical integration of electromechanical important direction of development. Second, the typical electromechanical integration products Mechanical and electrical subsystems integration products (complete machine) and the foundation yuan, part two categories. Typical mechanical-electrical integration system: CNC machine tools, robotics, automotive electronic products, intelligent instrumentation, electronic publishing printing systems, CAD / CAM systems. Typical electromechanical integration yuan, components are: power electronic devices and devices, programmable logic controller, fuzzy controller, micro-motors, sensors, ASIC, servo institutions. These typical electromechanical integration of technical status quo and development trends, market analysis of (not quoted). Third, China's development “mechatronics” the situation and tasks facing Mechanical and electrical integration mainly include two levels: First, by using microelectronic technology to transform traditional industries, and its purpose is energy and materials to enhance efficiency, improve product quality, the traditional industries of technological advances in improving step two is to develop automated, digital , intelligent mechanical and electrical products, and promote the upgrading of products. (A) China's “mechatronics” of the situation facing 1. China's microelectronics technology to transform traditional industries with the workload of large and broad, difficult 2. Electromechanical integration technology with China's accelerated product upgrading, enhancing the voice of the market share, pressure. 3. Electromechanical integration with China replaced by products of low technology content and added value, energy, water, supplies, pollution, disturbing product liability heavy and meaningful. China's industrial systems, energy consumption, water consumption big, serious environmental pollution enterprises also accounted for a fairly large proportion. In recent years China's industrial structure, product mix Although several adjustments, but for various reasons, lack of effectiveness has been obvious. This is a higher level inside leading departments from many doors, enterprises are “finding it hard to leave their native land”, “is entrenched industry”, but also optimize the undeniable not the ideal industry, the optimized no Italian products. The best answer long ago put these enterprises in the face, this is the development of mechanical and electrical integration, development and production of the electrical and mechanical integration products. Mechatronics product features strong, good performance, high-quality, low cost, and has a flexible, according to the needs of the market and reflect the user when the product mix and production process to do the necessary restructuring and reform, instead of switching equipment. This is the solution of mechanical and electrical products and more variety, the less important way to mass production. At the same time, for the traditional mechanical industries injection of fresh blood, bringing new vitality, and the heavy machinery production from the manual relieved to achieve civilized production. Furthermore, from the point of view of market demand, China's research and development of mechanical and electrical integration products with no long history, a big gap between the many varieties of product, quantity, grade, quality, can not meet the demand, larger than the annual import volume, much-needed development. (B) China's “mechatronics, ” the task China's mechanical and electrical integration, the task can be summed up in two sentences: The first observation is extensively used electromechanical integration technology to transform traditional industries; Another observation is that the mechanical and electrical integration in a big way to develop products, and promote the upgrading of mechanical and electrical products. The overall goal is to promote the formation of mechanical and electrical integration industry for China's industrial structure and product mix adjustment and make contributions. In short, electromechanical integration technology is to revitalize traditional electromechanical industrial source of fresh blood and driving force, is to open China's electromechanical industry products, the industrial structure adjustment of the keys to the door. Fourth, China's development “mechatronics” Countermeasures (A) strengthen the co-ordination arrangements, coordinated development plan Currently, the country engaged in “mechatronics” research and development and production of many units. Each had a set of its own development strategy. The units in their plans because of the foothold, the focus of the restrictions, it is inevitable to consider only local interests, the competent departments of the project and planning, lack of a unified consider, and make enough issue, the lack of authoritative Looking at the overall development plans and strategic planning. It is therefore recommended that the competent departments instruct the relevant units of in-depth investigation and study and scientific analysis on the basis of the overall development of a unified management “mechatronics” research, development, production plans and programmes to avoid duplication of development, production crashes! (B) strengthen regulation of the industry, to play the “Association” role At present, China's “mechatronics” more heat, while the current industry breakdown methods and management system, “from many doors” is the difficult pyridoxine. Therefore, it is necessary to clarify our country a “mechatronics” industry's management body, according to the country's political and economic reforms the spirit, as well as mechanical and electrical integration industry characteristics, we propose that the Beijing as soon as possible to strengthen the construction of the Electrical and Mechanical Integration Association, given its industry management functions. “Association” We should further expand the leadership - the representatives of the Governing Council and the level of coverage, we must strengthen the Office of the Secretariat building; able to pass its smart offices, economic entities, organizations, “industry” development, strategic planning fiction; guidance layout layout of the industry adjustment, the starting point for the development of options, do a good job of the pilot and key projects of the issuing of the project, the tender exercise…… (C) Optimization development environment, increased support for the Optimization development environment that through propaganda among the masses, creating a community as a whole, both inside and outside the enterprise to support “the mechanical and electrical integration, ” the atmosphere of development, such as China as soon as possible for foreign investors to invest in the development of “mechatronics” industry to provide convenient as possible for the establishment of development, production integration of mechanical and electrical products give the green light to high-tech enterprises; endeavour to develop, manufacture electromechanical integration products, such as the deployment of elements of good resources. Increase the intensity of support, technology policy, it is necessary to strictly limit the consumption of electricity, water, supplies high-traditional product development, did not use the mechanical and electrical integration of backward technology products restrictions mandatory elimination; strongly advocated using electromechanical integration on the traditional industries for the transformation of the electrical and mechanical integration technology to transform traditional industries dry on the technical development and application of project priority projects, and give priority support to the technical development and application of the unit to contribute to leadership, science and technology personnel of recognition incentives. (D) to highlight key development, take into account the “two levels” Mechatronics industries cover a very wide, and our financial, human and material resources are limited, so we grasp mechatronics industry development can not be exhaustive, Bengpuzhixu, it should distinguish between primary and secondary, bold choices, in order, selective. Attention should be paid to work on two levels. The first level is the “face” of work, namely the use of electronic information technology to transform traditional industries, in the traditional electromechanical devices implanted or grafted on Microelectronics (computer) devices, the “machinery” and “electronic” technology in the Jiancengci integrate. The second level is the “increase”, that is the beginning of the new product design, they “machinery” and “electronic” unified consideration, “machinery” and “electronic” inextricably linked, in-depth integration of the new production Products are at least do electromechanical integration. CONCLUSION: In this paper, in the careful guidance of teachers and strict requirements have been completed. Learning and life, will always feel the careful guidance of a mentor and selfless caring, I benefited. You are here to express our deep gratitude and lofty respect. Why not plot to step of a thousand miles, the smooth completion of the design, but also owe much to the datum related to the serious and responsible teacher, I can well understand and use our professional knowledge, and to be reflected in the design. At the same time, I collected a lot of online information before making my dissertation work smoothly. College of Engineering here to all teachers expressed heartfelt thanks.
收藏
編號:164949
類型:共享資源
大?。?span id="a14e2cm" class="font-tahoma">593.37KB
格式:RAR
上傳時間:2017-10-27
50
積分
- 關 鍵 詞:
-
轉速
加工
工藝
關鍵
癥結
樞紐
工序
工裝
設計
- 資源描述:
-
3919 轉速器盤加工工藝及關鍵工序工裝設計,轉速,加工,工藝,關鍵,癥結,樞紐,工序,工裝,設計
展開閱讀全文
- 溫馨提示:
1: 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
2: 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
3.本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
5. 裝配圖網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
裝配圖網所有資源均是用戶自行上傳分享,僅供網友學習交流,未經上傳用戶書面授權,請勿作他用。