單臂機器人-沖壓機械手及嵌入式機器人控制系統設計【含CAD圖紙、說明書】

壓縮包已打包上傳。下載文件后為完整一套設計?！厩逦瑹o水印，可編輯】dwg后綴為cad圖紙，doc后綴為word格式，所見即所得。有疑問可以咨詢QQ 197216396 或 11970985 摘 要傳統的工業機器人控制系統絕大多數是基于PC技術開發，但是，隨著嵌入式處理器性能的提高，這些領域的應用將會逐漸被嵌入式系統所取代。本文基于ARMV7架構的嵌入式處理器STM32實現對沖壓機器人的控制，并同時完成沖壓機器人機械本體的構造。設計出具有較高自動化程度和動態性能的單臂沖壓機器人系統。本設計創新點在于：（1）將32位嵌入式處理器STM32ZET6和嵌入式實時操作系統C/OS-II引入到單臂沖壓機器人的控制當中，取代了傳統的PC、PLC控制系統，提高了系統的快速響應能力且大大降低了成本。（2）利用FLASH斷電數據保持的特性，開發出簡易的示教控制系統，提高了沖壓機器人的環境適應能力。本設計充分貫徹了結構化、模塊化的設計思路。首先根據沖壓機器人的設計要求確定出系統的總體方案，即，機械本體加嵌入式系統控制。然后，通過初步分析，將機械本體劃分為五大功能組件，即，機械臂組件、升降滑塊組件、升降支撐組件、回轉支撐組件和底部框架組件，而后，通過建立CAXA三維實體模型確定出機械本體的具體設計方案，并對設計尺寸進行初步的確定和產品選型。接下來，對控制系統進行了設計，控制系統被總體劃分為軟、硬件兩大設計部分。硬件設計部分被進一步細分為電源電路、通信電路、控制器電路三大模塊；軟件設計部分則被細分為 uC/OS_II操作系統、觸摸屏控制程序、復位程序、五路脈沖輸出、示教程序等五大模塊。最后，在完成模塊化劃分的基礎上，根據已有知識和現有產品對該單臂沖壓機器人項目進行詳細設計和選型。關鍵詞：嵌入式；單臂沖壓機械人；STM32；示教系統；自動化ABSTRACTMost traditional industrial robot control system based on PC technology.However, with the improvement of embedded processor performance, applications in these areas will gradually be replaced by embedded systems. This article is based on the ARMV7 architecture embedded processor STM32 and construction of complete stamping at the robot mechanical body. Designs with a higher degree of automation and the dynamic performance is very good.The designs innovation is: (1) Comebined the STM32ZET6 32-bit embedded processor with the embedded real-time operating system C/OS-II into the single-arm punching robot control, instead of the traditional PC, PLC control systems and improved systems responsiveness while significantly reducing costs. (2) using FLASHs data characteristic, developed a tutorial for a simple control system, improved stamping robots ability to adapt to circumstances. Full implementation of this design is structured, modular design ideas. Firstly,Depending on the pushing robots requirements to determine the general scheme of the system, namely, mechanical body、embedded system control. Then, by a preliminary mechanical analysis,the mechanical body is divided into five major functional components, namely, the Picker Assembly, lift the slider component, elevating support assemblies, Rotary bearing components and the bottom frame components, which, through the creation of CAXA three-dimensional entity model to determine the specific design of the mechanical body, and preliminary determination of design size and product selection. Next, the control system was designed control systems are generally divided into two major design software and hardware parts. Hardware design part is further subdivided into the power circuit, communication circuits, controller circuit, three modules; software design portion was subdivided for the uC/OS_II operating system, touch screen controls, reset procedure, five pulse outputs, demonstration program and other five modules. Finally, upon the completion of the modular division,Detailed designing and selectioning of the single-arm punching robot project is based on the existing knowledge and available products. Keywords: embedded; single-arm punching robot;STM32;teaching systems;automation目 錄1 緒論11.1設計背景及意義11.2 工業機器人的國內外研究現狀11.2.1國內研究現狀11.2.2國外研究現狀21.3設計完成的工作和創新點31.3.2嵌入式控制系統41.4存在的問題及后續設計展望61.5論文總體結構62 總體方案設計72.1系統總體簡介72.2機械本體各部分設計方案及功能介紹82.2.1機械臂組件82.2.2回轉支承組件82.2.3升降支撐組件92.2.4升降滑塊組件92.2.5 底部框架組件102.3控制系統設計方案102.3.1嵌入式系統硬件102.3.2嵌入式系統軟件102.4本章小結113 關鍵部位的選型與校核123.1回轉支撐組件部分123.1.1電機M1及其減速機的選型與校核123.1.2推力球軸承靜載荷校核153.1.3螺釘校核163.1.4聯軸器鍵校核173.2機械臂組件部分183.2.1絲杠1選型與計算183.2.2電機M4選型與校核203.3升降支撐組件部分223.3.1絲杠2的選型與計算223.4升降滑塊組件部分233.4.1電機M3及其減速機的選型與校核233.4.2齒輪校核253.5本章小結274 控制系統設計284.1嵌入式硬件系統方案284.1.1電源電路284.1.2 控制器電路284.1.3通信電路324.2嵌入式軟件系統方案334.2.1 uC/OS_II操作系統334.2.2 觸摸屏控制程序354.2.3 復位程序364.2.4 五路脈沖輸出364.2.5 示教程序365 結論與展望37參考文獻39附錄1 程序流程圖40附錄2 主程序42附錄3 控制器原理圖46翻譯47英文原文47中文翻譯608.參考文獻70致 謝71